🇲🇽 ES | 🇺🇸 EN
+52 (81) 1636-1511 Monterrey, N.L. México
Back to Academy

Seam Welding: What It Is, Types and Welding Wheels

Continuous, leak-tight resistance welding with wheel electrodes

Seam welding is a resistance welding process in which the electrodes are rotating copper wheels. The sheets travel between the wheels while current pulses are applied, producing a row of overlapping spots that forms a continuous, leak-tight joint.

The core idea: it is spot welding in which each spot overlaps the previous one. That is why a seam weld seals and a spot weld does not.

How Does Seam Welding Work?

1. The wheels clamp and drive

Two wheels (or one wheel against a bar or mandrel) hold the sheets under constant force and move them forward as they rotate.

2. Current is applied in pulses

Each pulse forms one weld spot. Between pulses there is a cool time that keeps the sheet and the wheel from overheating.

3. The spots overlap

Travel speed and pulse rate are set so that each spot overlaps the one before it. The result is a seam that is tight to liquids and gases.

Heat is generated as in any resistance weld (Q = I²Rt). Because the wheel works continuously, it is almost always cooled with water applied directly to the weld zone.

Types of Seam Welding

Lap seam

The two sheets overlap and are welded along the lap. The most common form in tanks and containers.

Mash seam

The overlap is very small and the wheels mash it down during welding. The joint ends up nearly flush, close to the thickness of a single sheet.

Roll spot

Pulses are spaced apart to leave separate spots instead of a continuous seam. Used where strength is needed but leak tightness is not.

Continuous or intermittent

In continuous seam welding the wheel never stops. In intermittent welding it stops at each spot: slower, but used on heavier gauges.

Where Is Seam Welding Used?

  • Fuel tanks and automotive reservoirs.
  • Radiators and transformer tanks.
  • Drums, pails and cans.
  • Water heaters and thin-wall pressure vessels.
  • Mufflers and exhaust systems.

What Material Are Seam Welding Wheels Made Of?

The wheel is an electrode: it has to carry high current while resisting force and heat without deforming.

RWMA Class 2 copper (C18200 or C18150)

The most widely used material for seam welding wheels on carbon steel. A good balance of conductivity and hardness. See Class 2 copper.

RWMA Class 1 copper (C15000)

Higher conductivity. Preferred on coated sheet or aluminum, where the wheel tends to stick. See Class 1 copper.

RWMA Class 3 copper

Higher hardness. Used where welding force is high, as with stainless steel. See Class 3 copper.

A forged wheel has a denser, more uniform grain than one cut from plate, so it wears more evenly. See our forged wheels for seam welding.

Common Problems and Their Causes

Leaks in the seam

The spots are not overlapping: travel speed is too high or the pulses are too far apart.

Surface burns and spatter

Too much current, not enough cooling, or a wheel face contaminated with coating picked up from the sheet.

Seam width that drifts

The wheel face has spread with use. The profile has to be redressed to restore the original contact width.

Seam Welding FAQ

What is seam welding?

It is a resistance welding process in which the electrodes are rotating copper wheels. The sheets travel between the wheels while current pulses are applied, forming a row of overlapping spots that gives a continuous, leak-tight joint.

What is the difference between spot welding and seam welding?

In spot welding each weld is separate from the next. In seam welding the spots overlap thanks to the wheel electrodes, so the joint is continuous and seals against liquids and gases.

What are seam welding wheels made of?

Usually RWMA Class 2 copper (C18200 or C18150). Class 1 (C15000) is used on coated sheet or aluminum, and Class 3 where welding force is high, as with stainless steel.

What is mash seam welding?

A variant of seam welding in which the overlap between sheets is very small and the wheels mash it down while welding. The joint ends up nearly flush, close to the thickness of a single sheet.