🇲🇽 ES | 🇺🇸 EN
+52 (81) 1636-1511 Monterrey, N.L. México
Back to Academy

Projection Welding: What It Is, How It Works and Which Electrodes It Uses

The process used to weld nuts, studs and brackets to sheet metal

Projection welding is a resistance welding process in which current and force are concentrated by small raised features —the projections— formed on one of the parts, instead of by the tip of the electrode. It is the process used to weld nuts, studs and brackets to sheet metal in automotive and appliance manufacturing.

In one sentence: in spot welding the electrode decides where the weld goes; in projection welding the part does.

How Does Projection Welding Work?

The principle is the same as in all resistance welding: heat is generated by current flowing through the contact resistance (Q = I²Rt). What changes is where that contact happens.

1. Squeeze

Two flat, large-faced electrodes clamp the parts. The only contact between them is at the projections: embossments formed in the sheet, or features already present on the nut or stud.

2. Weld

All the current flows through those contact points. The projections heat up within milliseconds, soften and collapse under the electrode force.

3. Forge

Force is held while the metal solidifies. One weld nugget forms at each projection and the parts seat against each other.

Projection Welding vs Spot Welding

Where current is concentrated

In spot welding, at the electrode tip. In projection welding, at the projection on the part; the electrode only conducts and clamps.

Welds per stroke

One spot per stroke in spot welding. Projection welding makes several welds at once: a nut with three or four projections is finished in a single cycle.

Electrode life

The flat, wide face runs at a lower current density, so a projection electrode keeps its shape for more welds than a spot welding tip.

Weld location

Location is set by part geometry, not by electrode alignment. That is why projection welding repeats better in volume production.

What Is Projection Welded?

  • Weld nuts (square, hex and flange) on sheet metal.
  • Weld studs with projections or a ring on the head.
  • Brackets, bushings and reinforcements with embossed projections.
  • Cross-wire products: grids, racks and baskets, where the wire crossing itself acts as the projection.

Which Electrodes Does Projection Welding Use?

A projection electrode is stressed by force and temperature more than by current density, so harder materials are used than in conventional spot welding:

RWMA Class 3 copper (C17510 or C18000)

High hardness with good conductivity. The usual material for the body and face of a projection electrode. See Class 3 copper.

Copper-tungsten (Elkonite, Classes 10 to 12)

Brazed as an insert on the working face where wear and heat are high, such as high-rate nut welding. See Elkonite.

Guide pin

Locates the nut over the hole and must be electrically insulated so current does not flow through it. Made of ceramic or of steel with an insulating coating (KCF).

ALCAVIL manufactures these electrodes and pins to print. See the full line at projection welding electrodes and tooling.

Common Problems and Their Causes

One projection welds and another does not

Almost always lack of parallelism between the electrodes, or projections of uneven height: the tallest one takes all the current.

Expulsion and damaged threads

Too much current, too little force, or a slow weld head that cannot follow the collapse of the projection. The spatter ends up in the nut threads.

Off-center nut or weak weld

Worn guide pin. If it has also lost its insulation, part of the current shunts through the pin and the weld comes out cold.

Projection Welding FAQ

What is projection welding?

It is a resistance welding process in which current and force are concentrated by raised features (projections) formed on one of the parts. When current flows, the projections heat up, collapse and form a weld nugget at each one.

What is the difference between spot welding and projection welding?

In spot welding the electrode tip concentrates the current and one spot is made per stroke. In projection welding the projection on the part concentrates the current, the electrodes are flat, and several welds can be made in a single cycle.

What electrodes are used for projection welding?

Usually RWMA Class 3 copper electrodes (C17510 or C18000) and, where wear is high, copper-tungsten inserts (Elkonite, Classes 10 to 12) on the working face.

What is the guide pin for in nut welding?

It locates the nut over the hole in the sheet. It must be electrically insulated (ceramic, or steel with a KCF coating) so that current flows through the projections and not through the pin.